|
|
|
EXTENDER PORTU HDMI Z PRZESYŁANIEM SYGNAŁU SIECIĄ GIGABIT IP, ZASIĘG 120m
|
|
FUNKCJONALNOŚĆ
The XTENDEX® Low-Cost HDMI Over Gigabit IP Extender with IR and POE multicasts digital video and audio signals to one or more receivers up to 394 feet away over a 1000 Base-T Gigabit Network connected with CAT6/6a/7 cable.
Each Low-Cost HDMI Over Gigabit IP Extender with IR and POE consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display.
The local and remote units can be connected together for a Point-to-Point connection via CATx or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.
- Supports HDTV resolutions to 1080p.
- Extend up to 394 feet (120 meters) with CAT6/6a/7 cable.
- Extend up to 328 feet (100 meters) with CAT5e cable.
- Cascade network switches to extend the length long distances.
- Up to three switches can be cascaded.
- The max cable length between the first switch/transmitter and the last switch/receiver is 1,575 feet (480 meters) for CAT6/6a/7 or 1,312 feet (400 meters) for CAT5e cables.
- The max cable lengths between switches is switch dependent, but 394 feet (120 meters) is typical with CAT6/6a/7 cable.
- Power over Ethernet (PoE) – power supply not required at the local or remote unit.
- Ideal solution for digital signage applications.
- Broadcast real-time HDMI video and audio signals to multiple display locations with a managed or unmanaged (also known as non-managed) network switch.
- Transmits an HDMI signal over one CATx cable.
- Full Infrared Remote (IR) control of HDMI source from remote HDTV using existing source remote control.
- Plug-and-Play installation allows receivers to find the transmitters automatically on the same subnet. (Network configuration may be required for managed network switch.)
- Easily expandable. Add remote units as you add monitors.
- Inexpensive CATx cable replaces bulky video cables.
- Supports 1000 Base-T Ethernet connection.
- Built in default EDID table.
- HDMI 1.4 and HDCP 1.4 compliant.
- Support for multiple transmitters requires a managed network switch with VLAN support. Standard LAN switches can only support one transmitter.
- The managed switch must support port-based IEEE 802.1Q VLAN.
- Each VLAN acts as a separate HDMI Over IP Channel on the network.
- Each VLAN channel supports one transmitter.
- Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
- For a point-to-many connection, a standalone network with an unmanaged network switch, hub, or router can be used instead of a managed network switch.
- Up to 253 receivers supported.
- It is not recommended to use any other network devices on this standalone network as it may cause a degradation in performance.
- Local and remote units must be in the same LAN. The units do not support WAN connections.
|
|
SPECYFIKACJA TECHNICZNA
Moduł lokalny
- Gniazdo
„żeńskie” HDMI
do dołączenia źródła sygnału.
- One female 1000Mbps RJ45 port for sending high definition video/audio signals.
- Gniazdo "żeńskie" miniJack 3,5mm do dołączenia nadajnika sygnału podczerwieni IR (dostarczany w standardzie)
- Zakres częstotliwości IR: 20 do
60 kHz.
- Obsługa rozdzielczości
wejściowych: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz.
- Encoding delay: 80 ms latency
- Supports HDCP 1.4
Moduł wyniesiony
- Gniazdo
„żeńskie” HDMI-A
do dołączenia HDTV
- Gniazdo
„żeńskie” RJ45 (1000Mbps) do przesyłania wysokiej rozdzielczości
sygnału
video/audio.
- Gniazdo "żeńskie" miniJack 3,5mm
do dołączenia odbiornika sygnału podczerwieni IR (dostarczany w
standardzie)
- Zakres częstotliwości IR: 20 kHz
do 60 kHz.
- Obsługa rozdzielczości wyjściowych: 480p@60Hz, 576p@50Hz, 720p@50/60Hz, 1080p@50/60Hz.
- Obsługa zintegrowanego cyfrowego sygnału audio przez kompatybilne telewizory z portem HDMI lub odbiorniki audio.
- Supports HDCP 1.4
Zasilanie
- Power over Ethernet: With a switch that supports Power over Ethernet, a power supply is not required at the local or remote unit.
- Compliant with IEEE 802.3af, class 0 standards.
- Moduł lokalny i wyniesiony:
- Zasilane z zewnętrznych zasilaczy 230 VAC i 50 lub 60 Hz (opcja)
- Wyjście: 5VDC 3,0A
- Power Consumption:
Maksymalny zasięg
- 120 metrów (393 stopy) kablem kategorii CAT6/6a/7
- 100 metrów (328 stóp) kablem kategorii CAT5e
Kable
- Use HD-xx-MM cable to connect an HDMI source or display up to 50 feet.
- Use HD-ACT-xx-MM 4K HDMI Active Cables to connect an HDMI source or display up to 100 feet.
- Use DP-HD-xx-MM cables to connect a DisplayPort source up to 15 feet away from the transmitter.
- Use DVI-HD-xx-MM cable to connect a DVI source up to 5 meters.
- Use CATx solid or stranded straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors.
- Extend to 394 feet (120 meters) over CAT6/6a/7 cable.
- Extend to 328 feet (100 meters) over CAT5e cable.
- Cables not included.
Wymagania środowiskowe
- Temperatura pracy: 0°C do 60°C
- Temperatura przechowywania: -20°C do 70°C
- Wilgotność względna pracy i przechowywania: 0 do 95% bez efektu kondensacji
Wymiary
- WxDxH: 4.44x3.71x0.94 in (113x94x24 mm)
Certyfikaty
Gwarancja
|
|
|
Zestawienie
oferowanych urządzeń
|
Nazwa
|
Nr katalogowy
|
Instrukcja obsługi
|
Karta katalogowa
|
Low-Cost HDMI Over Gigabit IP Extender with IR and POE (moduł lokalny i wyniesiony)
|
ST-IPHD-POELC-V4
|
PDF manual
|
Karta katalogowa
|
Low-Cost HDMI Over Gigabit IP Extender with IR and POE (moduł wyniesiony)
|
ST-IPHD-R-POELC-V4
|
5V 3A Power Supply. Compatible with ST-IPHD-POELC-V4
|
PWR-SPLY-IPHDPOELCV4
|
Kabel z wtykami
"męskimi" HDMI
|
Nr katalogowy
|
Długość
|
HD-3-MM
|
0,9m (3 feet)
|
HD-6-MM
|
1,8m (6 feet)
|
HD-10-MM
|
3,0m (10 feet)
|
HD-15-MM
|
4,5m (15 feet)
|
HD-25-MM
|
7,5m (25 feet)
|
HD-30-MM
|
9,0m (30 feet)
|
HD-50-MM
|
15,0m (50 feet)
|
Kabel z
wtykami:
"męskim" DVI-D single link
i "męskim" HDMI-A
|
Nr katalogowy
|
Długość
|
DVI-HD-1M-MM
|
1m
|
DVI-HD-2M-MM
|
2m
|
DVI-HD-3M-MM
|
3m
|
DVI-HD-5M-MM
|
5m
|
|
|
|
|